Method Statement Title: Welding Procedure 1.0 Purpose To define the Method of Welding Pipe Lines. 2.0 Scope The Method is applicable to all Chilled Water Pipe work using mild steel and carbon steel pipes and fittings, for pipe sizes 65mm dia and above in accordance with Specification Section 15050, Clause 3.04, Clause 3.07 and our […]
Method Statement Title: Welding Procedure Read Post »
Method Statement Title: Start-up and Commissioning of Fans 1.0 Scope The scope of this Method Statement is to describe the procedure for pre-commissioning checks, start-up and commissioning of ventilation and pressurization fans installed within Burj Dubai – The Residences Project, in accordance with the Specification Section 15800. Note a. For installation of Fans, refer
Method Statement Title: Start-up and Commissioning of Fans Read Post »
Method Statement Title: Start up and Commissioning of Chilled Water Pumps 1.0 Scope The scope of this Method Statement is to define the method of Start-up and Commissioning of Tertiary Chilled Water Pumps installed in accordance with the Specification Sections 15700 & 15050. Note a. The testing and balancing of Chilled Water System will
Method Statement Title: Start up and Commissioning of Chilled Water Pumps Read Post »
Method Statement Title: Testing, Adjusting & Balancing of HVAC System SECTION 1 1. GENERAL REQUIREMENTS XXX Technologies as Independent Testing & Commissioning agency will perform the Testing, Balancing and Adjusting of the HVAC System in compliance with the specified tolerance and limitations outlined with CIBSE & BSRIA standards, guidelines and with reference to project specification.
Method Statement Title: Testing, Adjusting & Balancing of HVAC System Read Post »
Method Statement Title: Installation of pressurization Fans 1.0 Scope 3.2 Threaded rods, fasteners for supports. 3.3 Duct flexible connections. 3.4 Electrical cables, controls and accessories. BMS interfacing shall be done as defined in Material Submittal No.NMX/BDR/4045/GEN/CD/10809 dated 10.10.04 (ETA 024, Rev.3) 8.2 Signed off Fan’s installation checklist. 9.1 Installation check list for Pressurisation Fans.
Method Statement Title: Installation of pressurization Fans Read Post »
Method Statement Title: Installation of HVAC Ductwork 1.0 Scope : 2.0 Purpose : 4.0 Material : 5.0 Method : 5.1 Storage Preparation for the traverse joints including the fixing of the flanges/profiles as applicable as per the construction schedule is carried out at workshop. Please refer attached Annexure-II (revised) 6.0 Installation :
Method Statement Title: Installation of HVAC Ductwork Read Post »
Method Statement Title: Installation of Fresh Air Handling Units (Floor Mounted) 1.0 Scope 4.6 Testing 8.2 Air Handling Unit installation checklist signed off by R&P.
Method Statement Title: Installation of Fresh Air Handling Units (Floor Mounted) Read Post »
Method Statement Title: Installation of Fans (Central Exhaust) Scope 8.2 Signified off Fan’s installation checklist.
Method Statement Title: Installation of Fans (Central Exhaust) Read Post »
Method Statement Title: Installation of Exhaust Fans (Parking Area) Scope 3.2 Threaded rods, fasteners for supports. 3.3 Duct flexible connections. 4.5 Electrical connections 4.5.1 Electrical power connections shall be done as per approved drawings. 4.6 BMS Interfacing BMS interfacing as defined in Material Submittal No.NMX/BDR/4045/GEN/CD/10809 dated 10.10.04 (ETA M-024, Rev.3) 8.2 Signed off Fan’s installation
Method Statement Title: Installation of Exhaust Fans (Parking Area) Read Post »
Method Statement Title: Installation of Chilled Water Pumps 8.2 Pump installation check list.
Method Statement Title: Installation of Chilled Water Pumps Read Post »
