METHOD STATEMENT FOR HANGERS AND ANCHORS AND SUPPORTS OF SERVICES INSTALLATION

METHOD STATEMENT FOR Hangers and Anchors and Supports of Services INSTALLATION

• TABLE OF CONTENTS

1. SCOPE

2. definitions

3. HEALTH  AND  SAFETY

4. OPERATION

5. installation  and  fIXATION

6. RESPONSIBILITIES

7. MANPOWER  REQUIRED

8. MATERIALS  REQUIREMENTS

9. EQUIPMENTs  REQUIREMENTs

10. WASTE MANAGEMENT

11. SPECIAL CONTROL MEASURES

12. SUPPORTING  DOCUMENTATION

13. DISTRIBUTION

1.SCOPE

• This procedure to clear the method of the supply, installations Hangers and Anchors and Supports of Services for the project.
• This document details Hangers and Anchors and Supports of Services Installation:
• Preparation of work.
• Delivery and inspection upon arrival of material at site.
• Installation of the system.

2. definitions

           PQP             : Project Quality Plan

PSP              : Project Safety Plan

QCP             : Quality Control Procedure

HSE             : Health, Safety and Environment

MS               : Method Statement

ITP               : Inspection Test Plan

QA/QC         : Quality Assurance / Quality Control Engineer.

WIR              : Inspection and Test Request

MIR              : Material Verification Record.

3. HEALTH  AND  SAFETY

• Strictly followed as per the manufacturer’s Health and Safety recommendations for handling and use of the materials.
• Ensure all involved personnel shall be aware of the same.
• Specific safety measures have to follow as applicable, and all the safety measures are covered separately in the project safety plan.

4. OPERATION

• Material:
• Material used will be as approved by the Engineer.
• The sizes and routes routing will be as per the approved Shop Drawings.
• Storage and Protection: 
• Deliver components parts to site, completely identified in accordance with shop and certified CAD Drawings prepared for this work.
• Store in accordance with the manufacturer’s instructions, above ground, properly protected from the weather and construction activities.

5. INSTALLATION and Fixation

• Pre-Installation:
• All materials and documentation relevant to this particular section of works will be checked and verified ensuring that  these are correct and approved type.
• Prior to the commencement of works, ensure that the areas for permanent installation are ready, accessible and in suitable condition.

• Installation:
• After examine conditions at the job site where work shall be performed to insure proper arrangement and fit of the work, we will coordinate the drawings and specifications in order to insure the completeness of the work required. Verify measurements and dimensions at the job site and cooperate in the coordination and scheduling of the work.
• Proceed with installation of hangers, supports and anchors only after required building structural work has been completed in areas where the work is to be installed. Correct inadequacies including (but not limited to) proper placement of inserts, anchors and other building structural attachments.
• We will install hangers, supports, clamps and attachments to support piping properly from building structure, directly mounted with the Hollow core slab by using the M10 Unfix and the threaded rod M10 will be installed directly inside the unfix and we will arrange for grouping of parallel runs of horizontal piping to support together. Where supporting piping of various sizes together by trapeze hangers, space hangers for smallest pipe size or install intermediate supports for smaller diameter pipe.
• Install hangers and supports complete with necessary inserts, bolts, rods, nuts, washers and other accessories. Except as otherwise indicated for exposed continuous pipe runs, install hangers and supports of same type and style as installed for adjacent similar piping.
• We will adjust hangers so as to distribute loads equally on attachments and we will provide grout under supports so as to bring piping and equipment to proper level and elevations.

• Technical Assistance:
• The installation supervising technician for the system trade shall instruct the CONSULTANT Engineer, and Construction Site Manager on the programming and correct operation of the system after the installation is completed.
• This instruction shall be scheduled at the convenience of the staff.
• All such instruction shall be properly recorded.
• WIR will be issued for Consultant approval upon making sure that the installation of the system equipment’s done as per approved shop drawings, approved specs and manufacturer recommendations.

6. RESPONSIBILITIES

Ø  PROJECT MANAGER

1. To ensure that all the preparation and application works are carried out according to the Contract Specification and with the approved drawings.
   1. To ensure that the progressing of works is carried out according to the planned program and as per the approved method of statement.
   1. To ensure that all the equipment and material required executing the work are available according to the planned construction program.
   1. To co-ordinate with the Main contractor, MEP coordinator, Safety Officer for a safe and proper execution of the works.

Ø  SITE ENGINEER

1. To ensure that the works are carried out according to the Contract Specification, approved method statement and the shop drawings.
   1. To provide all necessary information and distribute responsibilities to his construction.
   1. To monitor the progress of work in relation with the work program and to report to the Project Manager.
   1. To co-ordinate with the safety officer and to ensure that the works are carried out in safe practicing method.

Ø  FOREMAN

1. The foreman will carry out his duties by maintaining continuous coordination with the site engineer on daily basis, and ensure proper distribution of the work force on the required and planned locations.
   1. To ensure that his assistant foreman/ charge hand are aware of the job requirements and they have enough information to carry out their duties properly.
   1. To ensure that the daily work is progressing as planned and advice the site engineer of any requirement for additional resources.
   1. To ensure in consultation with the site engineer that the manpower involved in the works are moving as agreed and planned for the work.
   1. To control disposal of waste materials according to the instructions received from the site engineer.
   1. To ensure full coordination with the safety officer to maintain safe working and proper house keeping of the site, following the proved safety measures and further ensure that all his working team are aware of the same to prevent accident and losses.
   1. To inform the site engineer regarding areas ready for inspection.
   1. Foreman and the storekeeper are responsible for the distribution and control of materials.

Ø  SAFETY ENGINEER

1. Ensure the implementation of all the safety measures in accordance with the HSE plan and everybody aware of it for it’s proper implementation.
   1. Ensure all the implemented safety measures are adequate to maintain safe working on the site.
   1. Inspect all the site activities and train the person to prevent accidents and it’s proper implementation.
   1. Ensure that the site is maintained clean and tidy.

Ø  TECHNICIAN FROM SUPPILER

1. The carrying-out of work and the proper distribution of all the available resources in coordination with the sub-contractor Site Engineer on a daily basis.
2. Daily reports of the works are achieved and coordinated for the future planning with the Site Engineer.
3. Complying with the sub-contractor basic design practices, particularly those related to safety and engineering
4. Meeting with any type of unforeseen incident or requirement and reporting the same to the Site Engineer immediately.

Ø  STORE KEEPER

1. Responsible for overall Store operations in making sure to store the material delivery to the site and keep it in suitable area that will keep the material in safe from rusty and damage.
2. One who will acknowledge the receiving of materials at site in coordination with QA/QC and concerned Engineer.

7. MANPOWER  REQUIRED

• Charge hand and Experienced Technicians

8. MATERIALS  REQUIREMENTS

• Hangers and Anchors and Supports of Services Components and Accessories.

9. EQUIPMENTs  REQUIREMENTs

• The Equipment  that will be engaged for Hangers and Anchors and  Supports of Services Installation will be as follows:
• Wire cutters

2. Measuring tape
3. Drill machine
4. Wooden hammer
5. Flat file
6. Screw drivers
7. Open and box spanners
8. Crimping tool

10. WASTE MANAGEMENT

• The Rubbish which would be created from our scope of works will be disposed to the designated dumping ground.

11. SPECIAL CONTROL MEASURES

• The following general control measures against Safety, Environment and Quality shall be required for our scope of work and special control measures are not applicable for us :
• Proper PPE must be worn at all time
• Permit to work at height > 2m where applicable
• Lifting operation permit (using crane) where applicable.
• Confined space permit where applicable.
• Approved work method statement and risk assessment will be made available to site.
• All workers doing the work shall be briefed on this method statement and risk assessment.

12. SUPPORTING  DOCUMENTATION

• This method Statement should be read in conjunction with the below referenced documentations:

• ITP for Anti – termite Treatment.
• Insulation Resistance and continuity Test Report.

13. DISTRIBUTION

• Copy of this method statement shall be issued to the following for information/ action/ comments:

1. Project Manager
2. Site Engineer
3. Foremen
4. Safety Engineer
5. Technician From Supplier
6. Store Keeper