CONTENTS 1.0 PURPOSE 2.0 SCOPE 3.0 REFERENCES 4.0 DEFINITIONS 5.0 RESPONSIBILITIES 6.0 EQUIPMENTS 7.0 PROCEDURE 8.0 ATTACHMENTS 1.0 PURPOSE This method statement is applicable for Supply & Installation of Plumbing Fixtures, Sanitary Wares & Accessories for the project as mentioned in the Approved Shop Drawings for Drainage System. 2.0 SCOPE Supply & […]
CONTENTS 1.0 PURPOSE 2.0 SCOPE 3.0 REFERENCES 4.0 DEFINITIONS 5.0 RESPONSIBILITIES 6.0 EQUIPMENT 7.0 PROCEDURE 8.0 ATTACHMENTS 1.0 PURPOSE The purpose of this method statement is to outline the method for handling, storage, installation, testing and commissioning for the Clean Agent System in accordance with the requirements specified in the relevant NFPA Codes, Standards and
METHOD STATEMENT FOR INSTALLATION, TESTING & COMMISSIONING OF CLEAN AGENT SYSTEM Read Post »
CONTENTS 1.0 PURPOSE 2.0 SCOPE 3.0 REFERENCES 4.0 DEFINITIONS 5.0 RESPONSIBILITIES 6.0 EQUIPMENT 7.0 PROCEDURE 8.0 ATTACHMENTS 1.0 PURPOSE This method statement is applicable for Installation & testing of Fire Fighting Piping system and its accessories in all areas for the project. 2.0 SCOPE Supply , installation & testing of Fire Fighting Piping system
CONTENTS 1.0 PURPOSE 2.0 SCOPE 3.0 REFERENCES 4.0 DEFINITIONS 5.0 RESPONSIBILITIES 6.0 EQUIPMENTS 7.0 PROCEDURE 8.0 ATTACHMENTS 1.0 PURPOSE This method statement is applicable for the Installation, Testing & Commissioning of External Fire Hydrant for the project as mentioned in the Specifications & Approved Shop Drawings. 2.0 SCOPE This method Statement shall cover
METHOD STATEMENT FOR INSTALLATION,TESTING & COMMISSIONING OF EXTERNAL FIRE HYDRANT Read Post »
CONTENTS 1.0 PURPOSE 2.0 SCOPE 3.0 REFERENCES 4.0 DEFINITIONS 5.0 RESPONSIBILITIES 6.0 EQUIPMENTS 7.0 PROCEDURE 8.0 ATTACHMENTS 1.0 PURPOSE This method statement is applicable for Installation & testing of all types drainage piping system in all areas for the project. 2.0 SCOPE
METHOD STATEMENT FOR INSTALLATION & TESTING OF DRAINAGE PIPE SYSTEM AND ACCESSORIES Read Post »
CONTENTS 1.0 PURPOSE 2.0 SCOPE 3.0 REFERENCES 4.0 DEFINITIONS 5.0 RESPONSIBILITIES 6.0 EQUIPMENT 7.0 PROCEDURE 8.0 ATTACHMENTS 1.0 PURPOSE This method statement is applicable for Installation & testing of Domestic Cold and Hot water supply Piping system and its accessories ( Above & Below Ground) in all areas for the project. 2.0 SCOPE Supply ,
1. AIR BALANCING A. Fan Coil Units 1 Check that all automatic controls are fully commissioned and operating properly 2 All pre-commissioning checks have been carried out 3 Select the specified speed of the Fan Coil 4 Set all the dampers in the grill outlet at full open position 5 Take initial total flow of
Air & Water balancing Method Statement Read Post »
SURVEYING AND SETTING OUT 1.0 OBJECTIVE: 1.1 Is to define the procedure for surveying and setting out works for the contract no GTC.101/ED/01 Engineering, Procurement, Installation and Commissioning (EPIC) of Ras Laffan Utilization Project –Buildings and utilities and support service Phase 1-Utilities. 2.0 SCOPE: 2.1 Applicable to all buildings and utilities at Base Area, New
Method Statement for SURVEYING AND SETTING OUT Read Post »
SUSPENDED CEILING WORK 1.0 OBJECTIVE To describe the procedure for installing suspended ceiling for the buildings under the contract no GTC.101/ED/01 Engineering, Procurement, Installation and Commissioning (EPIC) of Ras Laffan Utilization Project –Buildings and utilities and support service Phase 1-Utilities. 2.0 SCOPE To install suspended ceilings in the buildings at Service Berth, Service Base and
Suspended Ceiling Method statement Read Post »
FLOOR SCREED WORKS 1.0 OBJECTIVE 1.1 To describe the procedure, for laying of floor screed for the contract no GTC.101/ED/01 Engineering, Procurement, Installation and Commissioning (EPIC) of Ras Laffan Utilization Project –Buildings and utilities and support service Phase 1-Utilities. 2.0 SCOPE 2.1 Applicable to all the buildings in at Service Base Area, Service Berth Area,
Screed Method statement Read Post »
